Radium 20-1110 Fuel Hanger Surge Tank, Chevrolet Corvette C8 (2020+) - Walbro GSS342 / AEM 50-1200
Radium Engineering

Radium Fuel Hanger Surge Tank, Chevrolet Corvette C8 (2020+) - Walbro GSS342 / AEM 50-1200

$1,469.99

or 4 interest-free payments of $367.50 with Afterpay

Part no. 20-1110

1

Available to order - allow extra time for delivery

  • Shipped Australia-wideDelivery cost is shown at checkout. Shipping policy
  • Secure checkoutCard, PayPal and Afterpay accepted.
  • Not sure it fits?Contact us with your car and we'll check before you order.

Radium Fuel Hanger Surge Tank, Chevrolet Corvette C8 (2020+) - Walbro GSS342 / AEM 50-1200

Application: Chevrolet Corvette C8 (2020+) – RH fuel tank Part Type: In-tank fuel hanger surge tank (1-3 pumps) Part Number: 20-1110

The Radium Fuel Hanger Surge Tank allows 1, 2 or 3 aftermarket fuel pumps to be run in the stock RH fuel tank of the 2020+ Corvette C8, installing on the side opposite the OEM pump module. The 20-1110 version suits Walbro GSS342 and AEM 50-1200.

It can be configured three ways: as a true surge tank (direct injection only, or direct plus port injection), as a merged hanger for direct injection only, or as isolated direct and port injection systems. A venturi siphon jet pump draws fuel from outside the collector to the pump inlets (using 15-45 LPH depending on fuel pressure – allow for this when sizing pumps), while the one-piece anodised collector box is kept full by three 355 LPH one-way fill valves and fuel returning from the regulator. The 10AN ORB feed port has a low-profile 8AN male fitting, the return has a low-profile 6AN male fitting, and a 3/8in SAE quick connect is supplied for surge tank use.

Key Features

  • 1-3 Pumps: Run one, two or three aftermarket pumps in the RH tank
  • Three Configurations: Surge tank, merged hanger, or isolated DI and PI systems
  • Starvation Protection: Venturi jet pump plus three 355 LPH one-way fill valves
  • One-Piece Collector: Anodised aluminium collector box keeps fuel around the pump inlets
  • Low-Profile Fittings: 10AN ORB outlet with 8AN male fitting; return with 6AN male fitting
  • Lift Pump Port: 6AN ORB lift pump port with quick connect
  • Brushless Compatible: Suits brushless fuel pumps
  • High-Current Electrical: Anti-rotation stainless studs, nonconductive acorn nuts, ETFE wiring

What's Included

  • 8AN male fitting for the pump outlet
  • 6AN male fitting for the aftermarket return
  • 8.5mm barb for the OEM return
  • 6.5mm barb fitting for the OEM vent
  • OEM fuel sensor mount
  • Venturi siphon jet pump
  • Fuel-resistant submersible tubing
  • ETFE-insulated wiring
  • Pump inlet filtration
  • 6AN ORB plug
  • Stainless steel hardware

Optional Parts

  • Radium DIY Fuel Pump Hard Wiring Kit (17-0031) – one per aftermarket pump; upgraded wiring recommended for full pump power
  • Radium MPR RA Multi Port FPR Fuel Pressure Regulator (20-1100-00 / 20-1100-01) – multi-port regulator accepted by the 20-1279 FPR mount
  • Radium DFPR, Dual Fuel Pressure Regulator (20-1102) – dual regulator option for port-injection setups

Important Notes

  • Fuel pumps are not listed in Radium's kit contents
  • For Walbro F90000-series, Protec, Fuelab or DeatschWerks DW810 pumps see 20-1112; for the Ti Automotive E5LM see 20-1111
  • The rear subframe / drivetrain must be removed to access the OEM tanks – the engine is commonly removed as well
  • Each pump needs its own relay and fuse – order one wiring kit per pump (qty 1, 2 or 3)
  • The OEM FPR delete (Radium 20-1278) is only required for the merged configuration
  • Radium also offers a C8 FPR mount (20-1279, accepts 20-1100-00 / -01 or 20-1102 regulators) and an RWD fuel filter mount (20-1280) – contact Coore for availability
  • Radium's listing does not specifically mention right-hand-drive (Australian-delivered) C8s – confirm fitment with Coore before ordering
  • Installation instructions are available in the Instructions tab

Vehicle Fitment

  • Chevrolet Corvette C8 (2020+) – RH fuel tank

Not sure if this suits your vehicle? Email sales@coore.com.au and our team will confirm fitment.